1. Home
  2. Help
  3. What is a portal frame building

Guide

What is a portal frame building?

A portal frame is a steel frame made of two columns and two rafters, joined so stiffly at the corners that the frame holds itself up against the wind. That leaves a clear floor with no posts inside.

The short answer

Stand a steel column at each side of the building. Join them over the top with two sloping steel rafters that meet at the ridge. Bolt the corners rigidly. That is one portal frame.

Repeat the frame every 6 to 8 m along the building, tie the frames together with lighter steel, and cover the outside with steel sheets or insulated panels. That is a portal frame building.

It is the most common way to build single-storey sheds, workshops, warehouses and farm buildings in the UK.

The parts

  • Columns. The upright steel at each side of a frame.
  • Rafters. The two sloping beams that carry the roof and meet at the apex.
  • Haunches. The deeper steel at each corner where a rafter meets a column. They make the joint stiff.
  • Base plates and holding-down bolts. They fix each column to its concrete foundation.
  • Purlins and side rails. Lighter steel running along the building. Purlins carry the roof, rails carry the walls.
  • Bracing. Cross bracing in the roof and walls of at least one bay. It stops the building leaning along its length.
  • Cladding. Single-skin steel sheets, or insulated panels, with rooflights, doors and windows.

Every part, up close →

Usual sizes

  • Span: a single span is most efficient up to about 35 m.
  • Roof pitch: usually 5° to 10°, and 6° is the most common.
  • Frame spacing: 6 to 8 m between frames.
  • Haunch: about a tenth of the span long.
  • Purlins: usually 1.5 to 1.8 m apart.

These are starting points from Steel Construction Institute guidance. A structural engineer designs every frame for its own site.

Types of portal frame

  • Pitched-roof portal. Two columns and two rafters with a ridge in the middle. The common one.
  • Mono-pitch portal. One slope, for narrow buildings, lean-tos and canopies. Suits spans up to about 15 m.
  • Propped portal. A wide frame with a slim prop in the middle, where a central column is acceptable.
  • Tied portal. A tie between the eaves lets the columns be lighter, but reduces clear height.
  • Crane portal. Brackets on the columns carry rails for an overhead crane.
  • Mansard, curved and cellular. Shaped or perforated rafters, chosen for looks, height limits or long spans.

Any of them can have a mezzanine floor inside.

Why people choose one

  • Clear floor. No posts inside the span, so vehicles, racking and machines go where you want.
  • Made off site. The steel is cut and drilled to drawings, then bolted together on site.
  • Easy to extend. A building can often be made longer later by adding bays.
  • Your choice of skin. Uninsulated sheet for a store, insulated panels for a heated workshop.

Things to know

  • The corners take some height. The haunch hangs below the rafter, so clear height at the sides is a little under the eaves height.
  • Foundations matter. A portal frame pushes outwards as well as down, so the foundations are designed with the frame.
  • Sizes are to the steel. Span, length and eaves are measured to the outside of the steel frame. The cladding adds a little outside it.
  • Near a boundary, fire rules apply. The wall and the column bases may need to be designed to stay up in a fire.

What it costs, and whether you need permission

Price depends mostly on size, insulation, doors and how much of the work you want done. See guide prices by size →

Most new buildings need planning permission and Building Regulations approval. Planning permission for steel buildings →

How a steel portal frame building is measuredA cross-section of a portal frame with six numbered measurements: span to the steel line, size over the cladding, clear width between the columns, eaves height, clear height under the haunch, and roof pitch. 123456
  1. Span, to the steel line
  2. Over the cladding
  3. Clear width between the columns
  4. Eaves height, from the finished floor
  5. Clear height under the haunch
  6. Roof pitch, usually 5° to 10°

Ready when you are

Design your building in 3D, or tell us about your project.