1. Home
  2. Commercial & industrial
  3. Workshops

Workshops · Fabrication, repairs and trades

Steel workshop buildings

Clear-span workshops with big doors, good daylight and room to work around a vehicle or a bench. Insulated as standard so you can heat them in winter.

  • 9–24 mspans
  • 4–7 meaves
  • Up to 6 m widedoors
  • Freefirst design
3D render: Workshop

Typical 12 × 15 m workshop

180 m² · supply and erect from £228/m²

KitSupply only, with erection drawingsFrom £31,500
Supply and erectThe building, plus installationFrom £41,000
TurnkeyPlus foundations, slab, lighting and powerFrom £73,000

All prices exclude VAT. Guide prices. Delivery is priced separately. Itemised written quote after a site survey. Cost guide →

The example shown

What this example includes

This is the building in the picture and the guide prices above. Every item can be changed in the 3D designer.

  • Clear-span steel frame12 m wide with no posts inside · 4 frames
  • Size12 × 15 m · 180 m² · 4.5 m to the eaves
  • Gable door3 m wide × 3.5 m high
    x1
  • Side door3 m wide × 3.5 m high
    x1
  • Windows2.5 × 1 m each
    x2
  • Walk-through doorFor people, separate from the vehicle doors
    x1
  • Insulated walls and roof80 mm PIR insulated panels
  • ColoursWalls: White aluminium, RAL 9006Roof: White aluminium, RAL 9006Trims: Anthracite, RAL 7016
  • RooflightsRooflight panels in each bay
  • Design and drawingsDesigned for the wind and snow at your site, with a foundation plan

Delivery and installation are not included in the building price; each is priced separately. What is in the price, and what is not →

Ready-made

Enquire about this building

Workshop, 12 × 15 m, as shown. Nothing to design.

Rough cost, excluding VATFrom £31,500The building only (kit)

All prices exclude VAT. We reply with an itemised quote. Your details are used only to reply. Privacy

Before you design

Planning a workshop: decide these first

  1. Find your tallest jobA van on a lift or a tipped trailer body sets the eaves height. Measure it before anything else.
  2. Ducts before concretePlan sockets, three-phase machines and compressed air runs before the slab is poured, so the ducts go under the floor.
  3. The floorA power-floated, sealed slab is easier to keep clean. If you wash vehicles inside, ask your water company what the drains must run through.
  4. Noise and neighboursDoors that face away from houses make planning easier and the working day quieter.
  5. Heat where you workInsulated doors matter as much as insulated walls. A small heated zone can be cheaper to run than heating the whole building.
  6. Parking and turningCustomers, deliveries and vehicles waiting for work all need space outside.

More detail

The details

What this building does
  • Doors where you need them

    Sectional or roller doors on the side or gable, sized around your largest vehicle or machine, plus a personnel door to code.

  • Ready for lifting gear

    Columns can be designed for an overhead crane or a jib, so you don't have to strengthen the frame later.

  • Daylight on the bench

    Rooflight panels in every bay as standard on this layout, so you need the lights on less.

  • Warm enough to work in

    80 mm PIR insulated panels on walls and roof keep a small heater effective.

Typical specification

12 × 15 m workshop

Size
12 m span × 15 m long, to the steel line
Outside the cladding
12.45 × 15.45 m
Floor area
180 m²
Eaves height
4.5 m to the steel line
Height to ridge
5.84 m to the top of the roof
Clear inside
11.39 m between columns, about 4.0 m under the haunches
Roof pitch
10°
Frames
4 frames, 3 bays at 5.00 m centres
Cladding
80 mm PIR insulated panels
Colours
Walls RAL 9006 White aluminium · roof RAL 9006 White aluminium
Side doors
1 × 3 m wide × 3.5 m high
Gable doors
1 × 3 m wide × 3.5 m high
Personnel doors
1
Windows
2 × 2.5 × 1 m
Rooflights
Rooflight panels in each bay
Mezzanine
None
Fire protection
Not included

This is the starting point in the 3D designer. Every item can be changed.

What every building comes with

Every building is designed for the wind and snow at your site, and comes with a foundation plan for your groundworker and an itemised written quote for the option you choose: kit, supply and erect, or turnkey. Delivery and installation are not included in the building price; each is priced separately.

What is in the price, and what is not →

Size it for the work you do

Start from the job, not the floor area. These are typical sizes our customers choose.

UseTypical sizeEavesMain door
Single-trade workshop9 × 12 m4 m3 × 3 m
Vehicle repair, 2 bays12 × 15 m4.5 m3 × 3.5 m
Plant and agricultural repair15 × 18 m6 m5 × 5 m
Fabrication with overhead crane15 × 24 m7 m4 × 5 m

Guide sizes only. Add 600 mm clearance around anything you need to walk past.

What changes cost

Estimated change from the typical building above, supply and erect, ex VAT. Worked out with the same model as the 3D designer.

  • Raise the eaves to 5.5 mRoom for a van on a lift, or taller doorsfrom +£3,000
  • Add a second side doorDrive-through or a separate bayfrom +£2,500
  • Add another 6 m bayMakes it 12 × 21 mfrom +£10,000
  • Upgrade to 100 mm PIR panelsFor a workshop heated all dayfrom +£2,500
  • Add a 30% mezzanineStorage or a staff room over the backfrom +£10,500
  • Go turnkeyWe add foundations, slab, lighting and powerfrom +£30,500
Check it fits. The 3D designer opens this workshop with a car and a van inside. Add a lift bay or a forklift to check the eaves and door height.
Open in the 3D designer
Common questions
Can the workshop take an overhead crane later?

Only if the columns and foundations were designed for it. Tell us the crane capacity and span at the start and we'll design the frame, crane beams and pads to suit.

What door size do I need?

Measure your tallest and widest vehicle or machine, then add at least 300 mm each side and 300 mm above. Door height is limited by the eaves, less about 400 mm for the door head.

Do I need planning permission for a workshop?

Usually yes for a new building. Some extensions to existing industrial buildings in England can be permitted development under Class H. We prepare the drawings either way.

More advice and FAQs →

Planning and rules, in brief

  • Planning permission. Most new buildings need it. Your council decides.
  • Building Regulations. Almost every new building needs approval. Building control checks the structure, fire safety and, in heated buildings, the insulation.
  • The frame. Designed by a structural engineer to Eurocode 3, for the wind and snow at your site.

A guide for England, not legal advice. The rules we design to →

Design your workshop

Open this workshop in the 3D designer and change the size, doors and cladding.